Piping And Plumbing Fitting

Lightly oil the cone of the screw sleeve and the thread of the union nut. With sealing cone screw-on fittings with O-ring (AOL / AOS), the pre-stressing of the O-ring must be bridged and the sealing cone must lie metallically flush against the cone of the HL/HS connector. At this point, the cutting ring may be allowed to rotate, but must not move axially. Tightening torques for stainless steel fittings and for fittings with UN/UNF threads available upon request. The entire fitting consists of the threaded connector, the spacer ring with O-ring seal, the pressure ring and the union nut.

McAlpine valves, such as the McAlpine VP50P air admittance valve, features a dual-fit synthetic rubber finger seal for 3” or 4” soil pipe. Direct the flow of water outside a property with overflow pipes. Our range of PVC overflow pipes are available to buy in 30m, in either black or white. Aquaflow pipes come in a variety of sizes and shapes to complement the property design.

malleable iron pipe fittings manufacturer

Although reducers are usually concentric, eccentric reducers are used as needed to maintain the top- or bottom-of-pipe level. Gaskets are mechanical seals, usually ring-shaped, which seal flange joints. Commonly used gaskets are non-metallic (ASME B 16.21), spiral-wound (ASME B 16.20) and ring-joint (ASME B 16.20). Non-metallic gaskets are used with flat- or raised-face flanges. Spiral-wound gaskets are used with raised-face flanges, and ring-joint gaskets are used with ring-type joint flanges. Stress develops between an RTJ gasket and the flange groove when the gasket is bolted to a flange, leading to plastic deformation of the gasket.

Hydraulic fittings are designed and constructed to resist high-pressure leakage and sudden failure. The diverter tee is designed to allow flow to continue in the main line, even when the side branch is shut down and not calling for heat. Diverter tees have directional markings which must be heeded; a tee installed backwards will function very poorly.

With high peak-flow volumes, the design and construction of these systems may resemble those of storm sewers. Never let that be the case with our selection of copper tubes, stainless steel tubes and different plastic pipe options. Long radius pipeline bends are used in fluid transportation lines which required pigging. Due to their long radius and smooth change of direction, the pipe bend has very less pressure drop, and a smooth flow of fluid & pig is possible.

An advantage of this type of fitting is that the pipe it is connecting to does not need to be cut to a precise length; the slip joint can attach within a range of the end of the inserting pipe. Many slip fittings may be tightened or loosened by hand, for easier access to residential drainpipe systems . Because they operate at low pressure and rely on gravity to move fluids , drain-waste-vent systems use fittings whose interior surfaces are as smooth as possible. Freshly cut ends of pipe segments are carefully deburred to remove projecting slivers of material which may snag debris which can build up to cause blockages. This internal smoothness also makes it easier to “snake out” or “rod out” a clogged pipe with a plumber’s snake. An elbow is installed between two lengths of pipe to allow a change of direction, usually a 90° or 45° angle; 22.5° elbows are also available.

Elbows are generally available with an angle of 22.5o, 45o and 90o. If pipes are of same diameter then normal elbows are used otherwise Reducer elbows are used. These are generally coming with female threads and we can fix them by butt or socket welding also. Obviously, pipe fittings are attached to the end of pipes that allow them to change direction, control the flow, and change the diameter of the pipe. Being a non-trivial part of plumbing and piping systems, consulting us with your need is definitely advised to save yourself time, money, materials, and headaches. Unions are used as an alternative to flanges connection in low-pressure small bore piping where the dismantling of the pipe is required more often.

The flare nut, which had previously been installed over the tubing, is then tightened over the fitting to force the tapered surfaces tightly together. Flare connectors are typically made of brass or plastic, but stainless steel or other materials may be used. A solvent is applied to PVC, CPVC, ABS or other plastic piping to partially dissolve and fuse the adjacent surfaces of piping and fitting. Solvent welding is usually used with a sleeve-type joint to connect pipe and fittings made of the same material.